How to Take Back Wheel Off on an Electric Bike? Things You Need to Know When Removing Back Wheel of an Electric Bike.
If you have an electric bike, sooner or later, you will need to perform some basic repairs on it. These repairs can occur at any time and will not be as simple as tightening a loose screw.
One of the most common problems that electric bike owners face is a lack of knowledge of how to take the back wheel off on an electric bike without damaging any component.
When removing the back tire of your e-bike, you need to follow the basics steps, which are,
- Turn off or remove the battery
- Disconnect the motor cable and loosen the gear, disk brake cables
- Unscrew the nuts
- Take the tire off
Want to find out more about how to take the back wheel off of your e-bike?
Read this article to learn more about when to remove the back wheel, the steps of removing, anti-turn washers, tips for removing wheels and caring for your wheels, tubes and tires.
When Should You Remove The Back Wheel of a Bicycle?
There are a few incidents where you would need to remove the back wheel of your bicycle. Here are the most common reasons:
In The Event of Replacing Tube or Tires:
If you get a flat tire or punctured tube, you’ll need to remove the wheel to fix it. You might also want to remove the wheel if you’re replacing your tires with new ones.
In Hub Motor Repairs:
If your bicycle has a hub motor in the rear wheel, you’ll need to remove the wheel to access the motor. This is usually only necessary if the motor needs to be repaired or replaced.
In Accident Damage Repairs:
If your bicycle is involved in an accident and the rear wheel is damaged, you’ll need to remove it to make repairs.
In Storage:
When storing your bicycle, you may want to remove the rear wheel to save space. This is especially common with mountain bikes since they have larger wheels.
As you can see, there are a few reasons why you might need to remove the rear wheel of your bicycle.
In most cases, it’s a simple process that only takes a few minutes. However, if you’re unsure how to do it, you can always consult your bike’s owner’s manual and follow the steps below.
Steps to Remove The Back Wheel of an E-Bike
The following are the essential steps you need to take in order to remove the back wheel of an e-bike. Do remember that while these instructions are common for many bikes, your e-bike might have some specific quirks that you need to take into account.
Turn Off The Bike or Remove The Battery
This is an important safety measure to take, especially with electric bikes. Once the bike is off, or the battery is removed, you can begin to work on removing the back wheel. Otherwise, there is a chance that the electric components of your bike could get damaged while you are working.
Take The Chain Down to The Smallest Cogwheel of The Rear Wheel
Afterwards, an important step in removing the back wheel is to take the chain down to the smallest cogwheel of the rear wheel. This will give you some slack in the chain, making it easier to remove the wheel.
Unplug/Loosen The Wires & Cables Connecting to Back Wheel
There are usually a few wires and cables that connect the back wheel to the rest of the bike. Make sure to unplug or loosen these before attempting to remove the wheel.
Remove All The Nuts on Both Sides
Once the wires and cables are out of the way, you can begin to remove the nuts that hold the wheel in place. There are usually two or four nuts on each side of the wheel, depending on any additional accessories you have attached, so make sure to remove all of them.
Gently Take The Wheel Off
With all the nuts removed, you should be able to take the wheel off without too much trouble. Just be careful not to damage any of the parts as you remove them.
Now that you know how to remove the back wheel of an e-bike follow these steps the next time you need to do some maintenance on your bike. Just be careful and take your time, and you should be able to get the job done without any issues.
When putting the wheel back on, follow the same steps in reverse order. Make sure that all the nuts are tightened properly before taking your bike out for a spin. With these steps, you should be able to remove and replace the back wheel on your e-bike with ease.
YOUTUBE: https://www.youtube.com/watch?v=-mieLvdDI30
The Importance of Anti-Turn Washers
The anti-turn washers provide the wheel with extra stability during the ride, specifically when experiencing a lot of torque.
Most eBikes will have washers, and they are intended to be placed with the faces down and into the dropouts in the axle. When reassembling the rear wheel, be sure to replace the washers with their proper spacing, as it was earlier when removing them.
If the stack spacing is incorrect, it will adversely affect how the wheel sits inside the dropouts and, in turn, reduce its performance. If the washers aren’t correctly installed, your wheel won’t spin as true and will be somewhat wobbly.
YOUTUBE: https://www.youtube.com/watch?v=dh65XAgvrkU
Other Tips For Removing The Back Wheel of an E-Bike
Now that you know the basics of removing the back wheel of an e-bike, here are a few additional tips to make the process even easier.
Get a good set of tools: A good set of tools will make any bike maintenance task much easier. Make sure you have all the right sizes of wrenches and sockets before starting to work on your bike.
Remove the reflectors before removing the wheel: The reflectors are usually attached to the outside of the axle, so they can get in the way when you are trying to remove the nuts. It is a good idea to remove them before starting so that you don’t accidentally damage them.
Use a chain whip: A chain whip is a tool that helps to hold the cogwheel in place while you remove the nuts. This can be a big help, especially if you are working by yourself.
Be careful not to damage the parts: This is good advice for any bike maintenance task. Take your time and be careful not to damage any of the parts.
With these tips, you should be able to remove the back wheel of your e-bike with ease. Just be careful and take your time, and you should be able to get the job done without any issues.
Tips to Care For Your E-Bike Tires, Tubes And Wheels
It is very important to take care of your e-bike tires, tubes and wheels to help you avoid removing the wheels from time to time. Here are some tips on how to do so:
Tire Pressure: Check your tire pressure at least once a week. The correct pressure for your e-bike tires can be found in the owner’s manual or on the side of the tire. You can use a bike pump to inflate your tires.
Wheel Trueness: Check if your wheels are true once in a while. This can be done by spinning the wheel and observing it from different angles. If the wheel is wobbly, it is not true. So, it will need to be taken to a bike shop to be trued.
Rim & Spoke Condition: Inspect your rims and spokes for any damage. If there are any cracks or dents on the rim, it needs to be replaced. Also, check the spokes for any looseness. If any of them are loose, you will need to tighten them.
Overall, by following these tips, you can ensure that your e-bike tires, tubes and wheels are always in good condition!
Frequently Asked Questions Related to Removing The Back Wheel of an Electric Bike.
-
Is quick-release nuts or traditional nuts better for mountain bike tires?
There is a lot of debate about whether quick-release or traditional nuts are better for mountain bike tires.
Some people argue that quick-release nuts are easier to use and more convenient, while others argue that traditional nuts are more secure and less likely to come loose.
Ultimately, it comes down to personal preference. If you’re someone who likes convenience and ease of use, quick-release nuts may be the way to go.
However, if you’re someone who values security and safety, traditional nuts may be the better option. Whichever type of nut you choose, make sure to tighten them securely before hitting the trail.
-
What tools do I need to remove a bike wheel? Wrench, Pliers, Screwdriver
There are a few tools that you’ll need in order to remove a bike wheel, including a wrench, pliers and a screwdriver.
Use the wrench to loosen the nuts or bolts holding the wheel. Then, use the pliers to grab onto the tire and pull it away from the rest of the bike. Finally, use the screwdriver to remove any remaining screws or other fasteners.
Once everything is loose, you should be able to simply pull the wheel away from the frame of the bicycle.
-
What size is a bike wheel nut?
The bike wheel nut size is 3/8″ in diameter and 26 threads per inch. It is a difficult question to answer because there are so many different types of bike wheel nuts.
Some have a metric thread, and others have an imperial thread. Some are made of brass, and others are made of steel. The best way to find the answer to this question is to take your bike to a local bike shop and ask them for the correct size.
